Каталог решений

forward

Послепродажное головное устройство

Описание:
This USB 3.0 charger provides 5V @ 2.1A over an automotive input range of 8V - 40V. It uses the integrated FET TPS54340 PWM Buck controller and implements cable voltage droop compensation. A TPS2546 charging port controller provides data line switching plus an integrated FET with dual current protection thresholds.

Возможности:

8 to 40V (12V nominal) input voltage and 5V/2.1A output with TPS54340 Programmable voltage droop Supports both USB 2.0 and 3.0 power switch requirements This reference design has been lab tested and is supported with design files and an application note

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
The PMP10604 reference design is a 2-layer board 5V, 3A output power supply using LM53603 buck regulator for cluster unit in automotive applications. The LM53603 is a 3.5V to 36V input, 3A output capable, and 2.1 MHz fixed frequency buck regulator, specially designed for automotive applications. It has exceptionally low quiescent current (24µA typical at no load), and can transit to PFM from PWM to ensure high efficiency at light load. For this reference design, it has an input voltage range of 7.5V to 36V, covering the wide variation conditions of the 12V battery in automotive space. The reference board includes an input EMI filter section, and the layout is optimized for improved EMI performance on a 2-layers PCB. The board was tested under the automotive EMC standard, CISPR 25, and the conducted emissions were in compliance with the CISPR 25 Class 5 requirements.

Возможности:

7.5V to 36V input voltage range 91% peak efficiency EMI optimized 2-layout design, compliance with CISPR 25 Class 5 conducted emissions standard 2.1MHz fixed frequency, and seamless transition to PFM mode at light load Sub 75µA operating quiescent current The reference board is tested, and the test report and design files are included

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP10652 is a System optimized (CISPR 25 Class 3) 30W design for Surround View ADAS system. The design has various protections such as Load dump through TVS (ISO pulse testing), Reverse Voltage (Innovative Smart diode with very low Iq), Battery Disconnect Switch with OVP protection (PFET) and is EMI optimized to meet Conductive EMI limits of CISPR25 Class3 (overall) and Class5 upto 30MHz Range. Input voltage range is between 4.5V to 30V with OVP at 20V and hence will operate in most Cold Cranking conditions. LM74610 is used for Battery reverse protection which utilizes a charge pump to drive an N-channel FET to provide a resistive path for the bypass current to flow. LM53603Q1 is used as front end DC/DC Buck converter which is 2.2MHz switching, Synchronous rectified Wide Vin Buck Converter which can take transient upto 42V. TPS57114Q1 is used to provide power to the cores and it is a high current 2,2MHz switching buck converter. LM26420 is a dual 2.2MHz switching buck converter which is used for generating other required supplies. LM3880 sequencer is used for all the power up and power down sequencing requirements.

Возможности:

Designed for most Cold Crank and Start Stop conditions In compliance with the ISO pulse test / CISPR 25 Class 3 conducted emissions standard, passing both AM & FM radio band tests All devices Switching frequency at 2.1MHz (AM Band Avoidance) Reverse Protection through Smart diode Series Fault protection FET with OVP Power up and Power Down sequencing through integrated sequencer

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
Описание:
This design, incorporating the TPS65263, is a three output Synchronous Buck Converter intended for automotive radio tuners. The input voltage range is 6.5V to 16V, with all outputs designed up to 1A.

Возможности:

Designed for small size (24mm x 16mm) Switching frequency is 2 MHz All output are designed up to 1A

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP11136 reference design supplies cable drop compensated USB outputs of 5V @ 2.1A and 5V @ 1A. Additionally, there is a buck converter output of 3.3V @ 2.5A and a 12V @ 0.163A current regulated LED boost converter.
Возможности:

1.9MHz synrhronized operation on all switching regulators Low cost design Switched 12V @ 50mA antenna supply Multiple low noise linear regulator output options

Документация:
  • Схемотехника
  • BOM
Описание:
This solution is designed to be an automotive off-battery front end power supply for infotainment systems. It was created using a one stage power system meeting high voltage input needs and providing low voltage for multi output rails for different load needs. The system also provides transient and reverse polarity protection. The Wide Vin Buck stage is working at 2.1Mhz to avoid AM band and has superior EMI performance with an differential EMI filter to support CISPER 25.
Возможности:

Wide Vin 2.1MHz Integrated , Low Iq Buck Converter Boost for 5V CAN supply Transient and Reverse Polarity Protection and EMI filter added The system disconnet the second stage power and keep 3.3V sustained when Input votlage lower than 4.5V

Документация:
  • Схемотехника
  • BOM
Описание:
PMP40269 is a dual port car charger reference design. It has a USB Type-C™ port and a USB type-A port. The USB Type-C port can provide 5V 1.5A to USB Type-C device. The type-A port can provide 5V 2.4A, it is also capable of compensating for the effects on voltage droop when a smartphone or tablet is connected to the port using a long cable. It has a good system reliability with the integrated IEC ESD and short-to-VBUS protections. The solution efficiency is greater than 91% with USB switches at 12V input.
Возможности:

Fully integratedreference design for USB Type-C DFP port Short-to-VBUS protection on DP_IN and DM_IN IEC ESD protection on CC1/CC2 and DP_IN/DM_IN USB BC1.2 DCP charging protocols supported High efficiency up to 91.7% with full load

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
PMP40286 is a dual port car charger reference design. The output goes to a 5V 3A USB Type-C™ port and a 5V 2.4A USB type-A port. The USB Type-C port can be backwards compliant with BC1.2 and DCP configurations. The type-A port is capable of compensating for the effects on voltage droop when a smartphone or tablet is connected to the USB charger using a long cable. The solution efficiency is greater than 91% after USB switches at 12V input.
Возможности:

Fully integrated reference design for USB Type-C DFP port 91.4% @12Vin full load with USB switches Linear cable compensation for 75mOhm cable resistor in the USB type-A channel Integrated IEC ESD protection USB BC1.2 DCP charging protocols supported

Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
The PMP4465 is a reference design solution for powering MTK3360/70 processors used in automotive video applications. The TPS54360-Q1 provides a wide input voltage range of 7V to 42V and provides a stable 5V output for TPS65262-Q1. The TPS65262-Q1 integrates three buck converters and dual adjustable LDOs to get 5 regulated outputs. The PMP4465 provides a total solution from the battery to terminal loads.

Возможности:

High Integration solution Extra high efficiency at light load due to Pulse Skipping Mode (TPS65262) and Eco-mode (TPS54360) Input brown-out programmable Thermal Overloading Protection Small Size: 40mm(L)X40mm(W)x4mm(H)

Возможность заказа
  • Заказать BOM
Документация:
  • Схемотехника
  • BOM
  • Тестирование
Описание:
This reference design details a display power circuit which generates a bipolar voltage rail for source drivers and additional supplies for gate drivers. Charge pumps are used to generate the voltage supply for gate drivers, which makes this design easy to implement. By using only one dc-dc converter to generate four voltage rails and therefore minimizing the amount of inductances, this circuit allows small design size.

Возможности:

Complete power supply solution for TFT LCD display bias 4 output voltage rails Low quiescent current less than 0.5 mA Load regulation less than 2% on all rails Automotive qualified components

Документация:
  • Схемотехника
  • BOM
  • Топология платы
Описание:
This TIDA-00141 reference design provides a quick setup guide for a push-to-open/push-to-close motor drive system that enables the actuation of a flip up display for infotainment systems. This solution also demonstrates two methods of feedback: one using limit switches and the other taking advantage of the current limit setting on the motor driver. Enabling a quick solution for faster time to market, this design uses all automotive qualified devices, allows direct battery connection, and requires no software effort. This design incorporates theTPS65320EVM board to create the solution.

Возможности:

Push to Open/Push to Close Folding Display brushed motor drive solution without an MCU Wide input voltage range of 3.6V to 40V for power IC Linear/Switcher combination circuit enables low standby currents Supports actuator motors with currents up to 1A Small solution size with efficient layout considerations AEC-Q100 qualified devices

Возможность заказа
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
  • Тестирование
Описание:
This reference design implements a video over LVDS solution for automotive infotainment applications.It highlights the support of multi-touch with haptic feedback, LCD backlight control, and ambient light sensing, without the introduction of dedicated support lines back to the host processor. This design is implemented using two boards. The main electronics board, SAT0059 is where the deserializer, microProcessor, backlight controller, haptics drivers and power supply are located. The LCD interface board, SAT0096, is a physical and electrical interface to a specific LCD panel. It connects to the SAT0059 through a Samtec board to board connector and provides connection points for the LCD panel, touchscreen, backlight connections and haptic drivers. The SAT0096 is designed for a Microtips UMSH-8596MD-20T display. If a different display is to be used, a new LCD Interface board would likely need to be designed.

Возможности:

Wide input voltage range: off battery 4.5V to 40V power supply All video and support communications through LVDS o Supporting 24 bit RGB Video o 400Kbps back channel I2C connection for multi-touch input Haptic feedback State of art I2C/SPI interface LED backlighting controller with dimming ratio of >10,000:1, switching frequency ~2.2MHz, hybrid dimming and saftey and fault tolerances/functions Backlight adjustable to inputs o Ambient light sensor o Thermistor inputs on the LCD and the back light to enable thermal protection

Документация:
  • Схемотехника
  • BOM
  • Топология платы
  • Тестирование
Описание:

TIDA-00314 - референс-дизайн сенсорных кнопок на металлической основе с интегрированной функцией виброотклика. В этом TI проекте используется технология преобразования индуктивности в цифровой код и тактильные драйвера компании Texas Instruments для обеспечения высокой точности реакции на нажатие и качества обратной связи с пользователем. Этот референс-дизайн демонстрирует технологии проектирования систем, компенсацию воздействия окружающей среды, защиту от электромагнитных помех. Посмотреть видеообзор по TIDA-00314 можно здесь.

Возможности:

  • Замена механических кнопок сенсорными с высоким разрешением величины изменения индуктивности при обнаружении прикосновения к металлу
  • Настраиваемые виброотклик и сигналы, обеспечивающие высокое качество взаимодействия с пользователем
  • Программируемая чувствительность к усилию прикосновения к кнопке (от легкого прикосновения до сильного нажатия)
  • Один сплошной лист с металлическими элементами кнопок, герметизацией и заземлением, защищающим от электромагнитных помех (EMI), воздействий воды, масла, пыли и других загрязняющих веществ
  • Возможна работа в перчатках, под водой (при герметизации), в условиях жесткого воздействия окружающей среды
  • Можно использовать путем нажатия с удержанием в нажатом состоянии или путем многоразовых нажатий
  • Реализованы три варианта кнопок:
    • 20 мм кнопка
    • 3 х 10 мм (две кнопки)
    • 3 мм кнопка
  • Альтернативные конфигурации могут быть выполнены с различным механическим дизайном

Возможность заказа
  • Заказать BOM
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
  • Топология платы
Описание:
The FDC2214 proximity and capacitivesensing design demonstrates the use of TI's capacitive sensing technology to sense and detect the presence of various objects. The design is a complete hardware and firmware solution. The firmware processes the data from one proximity sensor and two capacitive touch buttons via the FDC2214 to determine whether an object is in the intended sensing area. Dedicated colored LEDs light up once the device detects a target in close proximity to the board or detects a press on the buttons. The design is powered by one AA-battery.

Возможности:

Optimized to achieve maximum sensing distance and responsive button presses Standalone system powered via one AA-battery Firmware includes derivative integration algorithm to process raw data Demonstrates proximity and capacitive touch button applications Integrates FDC2214, MSP430FR5969, and TPS61029

Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:

В настоящее время для пользовательских интерфейсов в домашних применениях широко применяется реализация кнопок на основе емкостного сенсора. Решения, основанные на низкой разрешающей способности, не позволяют добиться необходимой надёжности и более быстрого отклика на действия пользователя. На аппаратной платформе проекта TIDA-00474 от TIдемонстрируется решение данных проблем благодаря использованию стойких к воздействию электромагнитных помех высокоскоростных преобразователей «ёмкость – цифровой код» с высокой разрешающей способностью (до 28 бит). Печатная плата разработана и протестирована в условиях нахождения в вытяжке. Для кнопок с емкостными сенсорами и большого радиуса действия датчика присутствия приводятся подробности реализации и результаты тестов.

Данный базовый проект имеет характер аппаратного решения.

Возможности:

  • Двухканальный датчик присутствия с высокой разрешающей способностью (28 бит), представляющий собой протестированную аппаратную платформу для реализации системы распознавания жестов
  • Реализация 6 кнопок с емкостными сенсорами для надёжного детектирования касания при наличии влаги и других помех
  • Стойкая к воздействию электромагнитных помех архитектура на каждом канале емкостного сенсора для исключения детектирования от распространённых источников шумов
  • Реализация датчика присутствия и результаты тестов для вариантов с медной фольгой на печатной плате и с оксидом индий-олово (ITO)
  • Низкое энергопотребления в режиме ожидания. Ток потребления менее 1 мА при питании от источника постоянного напряжения в режиме ожидания
  • Высокоинтегрированный LED-драйвер с цифровым диммингом, защитой от повышенного тока, защитой от повышенной температуры и настраиваемыми функциями выключения при пониженном напряжении
  • Возможность измерения температуры и влажности
  • Полностью протестирован для применения в вытяжном оборудовании

Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
The TIDA-00573 reference design provides a Class D based amplifier solution that allows it to be evaluated in the form factor of a typical Class AB amplifier. The design is optimized to mitigate thermals associated with audio amplifiers and to minimize switching noises associated with Class D amplifiers. This design is comprised of two parts. The 1st highlights the audio amplifier module while the 2nd highlights the circuitry needed to incorporate it into a base board. The pair of boards allows stand-alone performance testing of the design.

Возможности:

Able to withstand load-dump conditions Size/Space optimized design CISPR-25 tested EMI Able to withstand Start/Stop operation down to 5.6V

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
Описание:
TIDA-00733 is a reference design for an eight-channel, Class-D amplifier that is capable of driving 2-Ω loads and an off-battery step-down power supply with 5-V and 3.3-V outputs. The amplifier design provides audio inputs for each audio channel. A high-performance audio analog-to-digital converter (ADC) creates the digital data stream from the audio inputs and creates the digital timing for the system.
Возможности:

Operating voltage range: 4.5V to 18V Withstands transients to 40V 2.1 MHz switching frequency for both power supply and Class D amplifiers 45 watts per channel into 2 ohms at 10% total harmonic distortion plus noise Passes CISPR-25 Class 5 radiated emissions

Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
TIDA-00746 is a 17W system-optimized SMPS design for automotive infotainment processor power. The design has been tested for and passed CISPR25 Class 5 conducted EMI limits. All buck converters used in this design is switching above AM band (>1.85MHz). The design is divided into four major blocks: Front end protection: Various protections have been implemented, such as those against positive and negative pulses (ISO7630 Pulse 1, 2a, 3a/b) through TVS, reverse terminal protection through innovative smart diode (LM74610), and battery disconnect switch with OVP protection (PFET). EMI filter: a common mode and a differential filter for conducted EMI suppression. Low EMI front end DC/DC converter: LM53635-Q1 is a switching, synchronous 3.5A buck regulator and is used as a front end DC/DC converter in this design. This 2.1 MHz part is automotive optimized and has low EMI. Apart from the spread spectrum option, the device comes in an automotive-qualified Hotrod(TM) QFN package with wettable flanks, which reduces parasitic inductance and resistance while increasing efficiency, minimizing switch node ringing, and dramatically lowering EMI. Downstream POL buck converters such as, LM26420-Q1 (Integrated dual buck), TPS57114-Q1, and TPS57112-Q1: all POL switchers used in the design switch above AM band. For high frequency noise-sensitive rails, a ferrite bead filter is used.
Возможности:

Wide-Vin front end power supply for 10W-17W automotive Off-battery operation with reverse battery protection Series fault protection FET with OVP at input Passed CISPR25 Class 5 conducted EMI test All devices have an AEC-Q100 qualified version available Switching frequency: above AM band (>1.85 MHz) for all the converters used

Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-00783.1 reference design is a triple output wide Vin power module design. It provides 3.3V, 1.8V and 1.2V output, at 6W total power. The layout is optimized for space constrained applications.

Возможности:

LMZ36002 wide Vin power module with integrated inductor, 4.5V to 60V input, 2A output LMZ20502 nano module with integrated inductor 4.5V to 40V wide input range Power module design with minimum external components 400 sq. mm compact solution size This circuit board is tested, and the design files and test report are included

Документация:
  • Схемотехника
  • BOM
Описание:

Базовый проект TIDA-00801 представляет собой полноценное решение системы питания «point-of-load» (преобразователи напряжения располагаются близко к соответствующим нагрузкам) с возможностью работы при просадках напряжения батареи, которое поддерживает входное напряжение от 2 В. В нём используется повышающе-понижающий DC/DC-регулятор TPS43330A-Q1, который поддерживает входное напряжение с диапазоном от 2 В до 40 В и которой позволяет поддерживать не только работу системы «старт-стоп», но и холодный запуск двигателя. Интегрированная микросхема управления питанием TPS659039-Q1 способна питать такие специализированные процессоры, как TDA2x/DRA7xx, в режиме point-of-load. Также в проект входят переключатель нагрузки на 5 В/ 4 А TPS22965-Q1 и линейный регулятор TPS51200-Q1 для терминирования питания DDR.

Достоинства.

Поддерживает холодный и тёплый запуск двигателя, соответствует требованиям современных процессоров к секвенсированию без использования дополнительной логики, поддерживает различную периферию и является малогабаритным бюджетным решением.

Данный базовый проект имеет характер аппаратного решения.

Возможности:

  • Соответствует требованиям современных процессоров к питанию и секвенсированию
  • Поддерживает различные варианты запуска двигателя
  • Поддерживает различную периферию (I/O, память)
  • Малогабаритное решение
  • Бюджетное решение

Возможность заказа
  • Заказать PCB
Документация:
  • Схемотехника
  • BOM
Описание:
The TIDA-00804 reference design is a low-cost discrete power solution for the i.MX6Q quad core application processor. All the DCDC regulators operate at frequencies above the AM radio broadcast band to avoid interference with the radio and to provide a small solution size due to smaller filter components. The first stage DC-DC converter can support a voltage input range of 6V to 42V, allowing the design to support start-stop operation as well as load dump. The second stage DC-DC converters provide all the necessary power rails to power the i.MX6Q. No power sequencer is necessary for this design. The PWB is a 4 layer board with 2 oz. copper to provide good power dissipation at 85 C ambient.

Возможности:

Wide input voltage range: off battery 6V to 42V power supply to support start-stop system and load dump The DC-DC regulators all operate above 1.8 MHz to avoid AM band interference Very small form factor: 75mm x 58mm circuit board dimensions No power sequencer necessary Less than 5% ripple on all power rails

Документация:
  • Схемотехника
  • BOM
Описание:
An inductive sensing based incremental encoder knob design can provide a robust and low-cost interface for control inputs. It can reliably operate in environments which have dirt, moisture, or oil which would pose issues for alternate sensing technologies. This solution requires no magnets.
Возможности:

High reliability, contactless, encoder implementation suitable for dirty, wet, and other challanging environments Scalable to support multiples of 4 positions/rotation Minimal MCU requirements No permanent magnets required; operates effectively even with magnetic or electrical enviromental interference

Возможность заказа
  • Заказать PCB
Документация:
  • Даташит
  • Схемотехника
  • BOM
Описание:
TIDA-00987 is a reference design for Automotive Media Ports that require data transfer. This design has the capability to support USB 2.0 and USB 3.0 data through a 15W USB Type-C™ port. Customers can accelerate their media port systems by taking advantage of a complete reference design comprised of analog AEC-Q100 qualified integrated circuits (ICs) that are CISPR 25 Class 5 tested. This design creates a robust, flexible solution which allows the system to charge both USB Type-C and legacy devices all within a small 1in x 2.5in solution.
Возможности:

The LM74610-Q1 smart diode emulates an ideal diode rectifier and protects downstream devices in the case of reverse polarity. The TPS25810-Q1 and TPS254900-Q1 provide negotiation over the CC1/CC2 and D+/D- lines respectively to enable charging of either USB Type-C or legacy downstream devices. Small solution size based on typical media interface board dimensions of 2.5in x 1in. The components in this system provide Short-to-Battery protection and load dump protection against input transients up to 40V. By combining the HD3SS3212 with the TPD4E05U06-Q1 and optimized layout, this design demonstrates SuperSpeed compatibility with the USB Type-C connector without signal degradation. The automotive grade LM53635-Q1 optimizes the power supply through its unique Hotrod package and reduces parasitics in order to mitigate EMI without interfering with AM or FM band frequencies.

Документация:
  • Схемотехника
  • BOM
Описание:
This reference design provides protection and diagnostics for antenna modules for use in automotive infotainment and navigation systems. This design is an alternate solution for antenna low-dropout linear regulators (LDOs) for the purpose of achieving lower ohmic drop (IR) while meeting the necessary protection measures such as short circuit, short-to-battery, reverse current, and overvoltage protection. The design also meets the subsystem-level diagnostic requirements such as precise light load and overload detection.
Возможности:

Open Load Detection at 10 mA (Typical) Selectable Overcurrent Detection at 300 mA, 600 mA, 900 mA, 1.2 A Shutoff in 1 μs (Typical) to Short-to-Battery Fault Fast Response of 200 ns (Typical) to Short-to-Ground Fault Low IR Drop With TPS25940-Q1 (42 mΩ RON)

Документация:
  • Схемотехника
  • BOM
Описание:
This reference design is a high power, wide input voltage range circuit that uses synchronous boost controllers in a dual-phase configuration outputting four (4) switchable 12-V rails that each can supply up to 2.5 A with diagnostic features; plus a dual synchronous buck that generates two high current, lower voltage rails.
Возможности:

Wide input voltage range of 9V to 20V, support transient down to 6V and up to 36V Dual-phase high current synchronous boost controllers configuration with > 98% efficiency under typical operating conditions Dual high-current synchronous outputs: 5V, 3A nominal; 3.8V, 6.5A nominal Reverse battery protection with zero IQ smart diode controller Minimized AM radio band interference

Документация:
  • Схемотехника
  • BOM
Описание:
This reference design is a high-current, wide input voltage range circuit that can handle engine cold crank profile down to 2.5V. The dual-output voltages are 5V and 3.3V that support up to 10A for each output. The design is suitable for an automotive off-battery infotainment application that needs to support a very stringent starting profile down to 2.5V.
Возможности:

Wide input voltage range of 2.5V to 40V Dual high-current synchronous outputs: 5V, up to 10A; 3.3V, up to 10A Continuous operation during engine crank transient down to 2.5V Reverse battery protection with zero IQ smart diode controller Minimized AM radio band interference

Документация:
  • Схемотехника
  • BOM
Описание:
This automotive reference design demonstrates an approach for powering remote, off-board loads, often over coaxial cables (i.e. "phantom power"). This design is capable of protecting against and digitally diagnosing different faults that off-board cabling is susceptible to. Reverse polarity, reverse current, short to-battery, short-to-ground, and thermal shutdown are protected against and diagnosed through I2C and a fault flag. The integrated reverse-current protection does not require an external diode at the output of the device, which saves cost and avoids increasing the dropout voltage.
Возможности:

4.5V to 40V wide input voltage range and load dump of 45V Multiplexing current sense between channels/devices to save ADC channels High accuracy to detect antenna open, normal, over current, and short circuit conditions over current/short circuit Digital window comparator with programmable high & low thresholds and alert Output voltage adjustable 1.5 - 20V, output current up to 300 mA per channel

Документация:
  • Схемотехника
  • BOM
Описание:
Based on TI's Jacinto™ DRA71x processor, this automotive reference design focuses on system-level cost savings. The 6 layer design reduces PCB costs through an optimized via breakout scheme, integration of key features and an optimized power distribution network. Functionality can be added or removed based on the end-product requirements. This design targets applications such as infotainment and reconfigurable digital cluster; and supports HDMI, USB3.0/2.0, TAS6424 Digital Class D Amplifier, and FPD-Link interface and multiple other features. It includes a 12V input with a single PMIC. In addition, a Linux, Android, or QNX based software development kit is included.

Возможности:

TI Jacinto DRA71x processor with integrated features help customers design cost effective, feature rich, entry level (display audio) infotainment and cluster systems ARM Cortex-A15 based processor with 600MHz, 800MHz, and 1GHz speeds, as well as 3D/2D graphics, C66x DSP and Cortex M4 options Processor Software Development Kit (SDK) for Linux, Android, and QNX development Cost saving features include 6 layer hardware design, rear view camera support, tuner integration with software defined radio, Class D amplifier and multi zone audio support Includes TI's TPS65919 Power Management IC and TAS6424 Class D Audio Amplifier

Документация:
  • Схемотехника
  • BOM
Описание:
This dynamic Near Field Communication (NFC) tag design outlines the required components, layout considerations, and provides firmware examples to implement NFC into applications such as Bluetooth® and Wi-Fi® pairing, equipment configuration and diagnostics, or as a general purpose NFC data interface. The documentation, hardware, and example code provided allows the designer to quickly implement NFC functionality with an MSP430 or other MCU of choice.

Возможности:

NFC Tag Type 4B compliant design ISO14443B compliant 13.56-MHz RF interface supports up to 848 kbps for fast data transfer Code examples to write and read NDEF messages to internal SRAM 3kB SRAM for a large variety NDEF message types Interrupt register and output pin to indicate NDEF read or write completion for further processing This design is tested and includes firmware, hardware design, and a user's guide

Документация:
  • Даташит
  • Схемотехника
  • BOM

Сравнение позиций

  • ()